Sealant for mirror
• Primerless adhesion to numerous porous and non-porous substrates
• No shrinkage
• Does not crack or discolor
• It has a good adhesive strength without primer on most common materials such as aluminum, zinc, galvanized steel, stainless steel, copper, natural stone, concrete,
brick, etc.
• For crystal clear elastic bonding applications
• Invisible bonding and sealing of materials in indoor applications
Instructions:
• Before the application, the tip of the cartridges is cut and a plastic cap is fixed.
• For bonding application: Apply the adhesive in strips or dots to the base or on the element to be bonded. The strips must be applied in vertical rows. Bring together the
parts to be joined as quickly as possible, at least within 5 minutes(this depends on the temperature and relative humidity level).
• For sealing application: The surface of Akfix Clear applied in the joints should be smoothened with a dampened spatula, glazing tool, joint iron or by hand immediately
• If used, the adhesive tape should be removed afterwards
• The opened packages should be consumed as quickly as possible
• The contaminated areas and used tools should be cleaned with white spirit or alcohol. It is cleaned only mechanically after cured.
• Minimum width for bonding is 1mm
• Maximum width for bonding is 3mm
• Minimum width for joints is 5mm
• Maximum width for joints 10mm
• Minimum depth for joints 5mm
Consumption (approx.):
| Joint Width | 5mm | 10mm |
| Joint Depth | 5mm | 5mm |
| Efficiency /300ml | 12 meters | 6 meters |
Surface Preparation:
Following cleaning procedure and materials are recommended:
| Glass | Degrease with alcohol or MEK |
| Aluminium, light alloys and stainless steel | Degrease with alcohol or MEK |
| Other Metals | Lightly abrade then degrease as above |
| Wood | Lightly abrade surface then remove dust |
| Plastics | Degrease using an agent recommended by plastics manufacturer |
| Concrete and other alkaline Surfaces | Brush and remove dust |
Standards:
Meets or exceeds the requirements of the following specifications:
• The requirements of VOC content specifications in LEED credit EQc4.1 “Low-emitting products” of SCAQMD rule 1168
• The French VOC requirements for class A+
• CE marked for EN 15651 for façade & glazing applications (DOP NO: 2016-0004)
Restrictions:
• It must not be used in totally confined spaces where sealant cannot cure due to lack of atmospheric moisture.
• Cannot be used on natural stone. Because the adhesion surface will discolor under influence of the sealant (looks wet) and also this is visible through the sealant due to
its clear look
• Do not use in applications where continuous water immersion is possible
• Prolonged exposure to direct sunlight can cause discoloring
Storage & Shelf Life:
Safety & Disposal:
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data.
Properties:
| Chemical Base | AST Polymer |
| Curing System | Moisture |
| Density | 1.05 ± 0.03 gr/ml |
| Appearance/Color | Paste, Clear |
| Tack Free | 5-10 min (23°C and %50 R.H.) |
| Curing Rate | ~ 2,7 mm/ 24 hr (23°Cand %50 R.H.) |
| Shore A Hardness | 35 ±5 |
| Elongation at Break % | ≥ % 350 |
| Volume Loss | < -%3 (23°C and %50 R.H.) |
| Tensile Strength | 2,10 N/mm2 |
| Shear Stress | 1471-1606 Pa. |
| Viscosity (Pa.s) | 1440-1572 Pa.s at 25°C |
| Viscosity (cps) | 1440000- 1572000 Cps at 25°C |
| Heat Resistance | -20oC and +80oC |
| Application Temperature | +5oC and +40oC |
Prev：Silicone Sealant For PV Modules
Next：No nail glue
